FOR LIVE STEAM & BATTERY R/C LOCOS. JAN 1st 2020
Remote Control Systems (RCS)
DSM2/DSMX AUTO BIND RECEIVERS. |
||||||
FEATURE | LM0034-E | LM0034-T | AB-EM | AB-TM | RX107v2-E | RX107v2-T |
DISABLED FAILSAFE |
YES | YES | YES | YES | YES | YES |
AUTOMATIC BINDING |
YES | YES | YES | YES | YES | YES |
DIRECTIONAL F & R LIGHTING |
NO | NO | YES | YES | YES | YES |
SERVO REVERSING |
NO | NO | NO | NO | YES | YES |
SERVO E POINT ADJUSTABLE |
NO | NO | NO | NO | YES | YES |
LIST PRICE | A$ 29 |
A$ 29 | A$ 29 | A$ 29 |
A$ 39 | A$ 39 |
BRAND NEW DESIGN WITH AUTOMATIC BIND |
|
![]() ONLY A$ 39 EACH. GB £ 21. US $ 27. |
![]() ONLY A$ 39 EACH. GB £ 22. US $ 29. |
7 CHANNEL ADJUSTABLE - AUTOMATIC BIND RECEIVERS. * AUTOMATIC BINDING. |
Rx107v2 SOUND TRIGGERS USING RCS Tx HANDPIECES. All RCS handpieces can use Ch # 5 for a sound trigger. Usually a whistle or horn. |
# EVO-DUPLEX Tx's have one trigger per channel = 1 - 3 x Triggers max. |
# DUAL-USE Tx's require an R/C switch with 2 x triggers per channel = 3 - 5 Triggers max. |
IF R/C SWITCHES ARE REQUIRED THE INSTRUCTIONS HAVE AN APPLICATION GUIDE. USING MYLOCOSOUND WILL REQUIRE ADD ON R/C TRIGGERS. CLICK HERE FOR FOR FULL LIST OF SUITABLE R/C SWITCHES. |
Model | Price | Image | Description |
---|---|---|---|
ADJUSTABLE AUTOMATIC BIND (A-B) Rx'S. PUSHBUTTON SUPPLIED FOR SERVO ADJUSTMENT. |
|||
Rx107v2-EM-10![]() |
A$39 (L) | ![]() |
Xenon Rx's with Dual 10 cm Diversity antenna. End Mount pins. Clear heatshrink covered. PDF Instruction Manual @ 12/12/20 |
Rx107v2-TM-10![]() |
A$39 (L) | ![]() |
Xenon Rx's with Dual 10 cm Diversity antenna. Top Mount pins. Clear heatshrink covered. PDF Instruction Manual @ 12/12/20 |
Rx107v2-EM-20![]() |
A$39 L) | ![]() |
Xenon Rx's with dual 20 cm Diversity antennas. End Mount pins. Clear heatshrink covered. PDF Instruction Manual @ 12/12/20 |
Rx107v2-TM-20![]() |
A$39 (L) | ![]() |
Xenon Rx's with dual 20 cm Diversity antennas. Top Mount pins. Clear heatshrink covered. PDF Instruction Manual @ 12/12/20 |
PIN-8-pb![]() |
A$10 (L) US$7 |
![]() |
Push-button on plug in ZH cable for Pin # 8. Allows Intermediate Rx's to be programmed the same as # Rx107v2. Download how to program |
BATTERY REQUIREMENTS. | |||
The above receivers can use 4 x AA or AAA re-chargeable cells. (4.8 volts nominal). However, if the battery voltage sags below 4.6 volts, erratic behaviour can occur. For the best and most reliable performance we suggest at least welded packs of 4 or 5 x AAA rechargeable cells. Plastic holders & Alkaline cells not recommended. Alternatively you can use a # UBEC-5v regulator pcb and higher voltage batteries. Voltage range = 4.8 - 6.0 volts. Rx batteries are not needed with ESC's. The ESC provides the 5 volt supply. |
|||
U-BEC-5v![]() |
$15 (L) | BEC 3.0 Amp max 20 v in, 5 volt supply out for heavy duty servo use. Very useful if using MyLocosound in Live Steam locos. A 7.4 volt pack is ideal. |
|
PRE-WIRED PLUG IN HI-INTENSITY LED's FOR Rx's. Forward & Reverse lighting. Ballast resistors not needed. Red wire not used. MUST ONLY BE USED with AB-RXv2 & RX107v2. CAN BE USED AS AN LED(2). |
|||
LED-3mm-WW![]() |
A$10 (L) US$7 |
![]() |
20 cm servo lead with 1600mcd 3 mm Warm White LED. Front or Rear LED headlight. Requires heat protection if used with Live Steam. |
LED-5mm-WW![]() |
A$10 (L) US$7 |
![]() |
20 cm servo lead with 25000mcd 5 mm Warm White LED. Front or Rear LED headlight. Requires heat protection if used with Live Steam. |
LED-3mm-G![]() |
A$5 (L) US$7 |
![]() |
10 cm servo lead with a 3 mm Green LED. Use for externally observing what the Rx is doing when programming. Plugs into Front light. |
SERVO REVERSER. | |||
SIG-REV![]() |
A$5 (L) US$ 3 |
![]() |
For use with 4 x dry cells or 4 or 5 x rechargeable batteries. Ideal for Garrat type locos where one direction servo of the two needs to rotate backwards. |
HANDY PLUG IN DEVICE FOR MEASURING PULSE WIDTH. | |||
PULSE-MEASURE![]() |
A$29 (L) US$20 |
![]() |
Simply plug into any channel to measure the PWM of servo signal. |