5-6 CHANNEL AUTO BIND DSM2 RECEIVERS
FOR LIVE STEAM & BATTERY R/C LOCOS. SEP 1st 2019

  Remote Control Systems (RCS)
 
Model Price Image Description
2.4 GHz 5-6 CHANNEL RADIOS (Servos not inlcuded).

BRAND NEW DESIGN LOW COST!!! AUTOMATIC BIND
DSM2/DSMX 2.4 GHz receivers.
NOW AVAILABLE - INTRODUCTORY PRICING.



 Long Range. Disabled Failsafe. No lighting outputs. See below.
 
Can be used for Live Steam and Battery R/C.
Full range on one antenna only.
Optional extra low cost Servo Reversers if needed.
All Rx's are the same size. 30 mm x 18 mm x 12 mm.
For the AB-EM End mount servo pins allow extra length for servo plugs.
AB-EM
 A$29 (L)
US$ 20
 Long Range Xenon Rx's w/Diversity antennas.  Ideal for battery R/C   End Mount pins.
PDF Instruction Manual
AB-RA
 		A$29 (L)
US$ 20
 Long Range Xenon Rx's w/Diversity antennas.  Ideal for battery R/C  Top Mount pins.
PDF Instruction Manual
SAVE 15% BUYING A 4 X PACK.
AB-EM-4
 A$99 (L)
US$ 68		 4 X PACK BULK BUY OF ABOVE RX's
AB-RA-4
 		A$99 (L)
US$ 68		 4 X PACK BULK BUY OF ABOVE RX's
Do you need a Servo Reverser on the Ch # 1 steam regulator?

The short answer is probably yes.
Steam regulators on the backhead of Live Steam locos rotate CCW to allow steam to go to the cylinders, but, servos operate clockwise to mimic the Tx knobs. 
Thus, if the Steam Regulator and the servo working are parallel to each other, the servo will be reversed relative to the regulator valve. 
If you want to to twist the Tx regulator knob to the right (CW) to open the regulator and control loco speed, you can either mount the servo opposite the Steam Regulator, or use a Servo Reverser.
                                                      OR
You can think laterally and at the same time operate more prototypically.
Why not open the regulator by twisting the knob CCW, instead of CW?
You can still use the stock Tx handpiece for battery R/C. If you like this new "backwards" protocol, maintain it for Battery R/C by reversing the signal internally in the ESC.
LIVE STEAM SERVO REVERSERS SUPPLIED FREE.
 
USE WITH ANY RX THAT USES STANDARD SERVO SIGNALS.
Reverses any one servo that is backwards.
Useful when two servos are working together on one signal.  E.G. Garratt type locos. 
Needed if one servo throw is backwards relative to the other engine.  OK with Hi-Tec HS82MG.
Saves reversing the servo in linkages.
FOR LIVE STEAM MAXIMUM 4.8 VOLT NOMINAL.
T-SIG-REV(F)
 NO CHARGE

1 x supplied NO CHARGE when ordered with 1 x Rx.
T-SIG-REV
 A$4 (L)
US$ 3
 Maximum battery voltage = 4.8 volts nominal.
4 x 1.2 volt rechargeables only.
FOR LIVE STEAM MAXIMUM 6.0 VOLT NOMINAL.
SIG-REV(F)
 NO CHARGE 1 x supplied NO CHARGE when ordered with 1 x Rx.
SIG-REV
 A$4 (L)
US$ 3
 As above. For use with 4 x dry cells or
5 x rechargeable batteries.
End Mount pins. 
OTHER SERVO REVERSERS & THROW ADJUSTERS
MRW-10
 $ 24 (L)
US$16		 END POINT ADJUSTER & REVERSER.
Reverses servo & adjusts servo centre end points. 20 % adjustment.  35 mm x 18 m x 7 mm
PDF Instructions
MRW-11
 $ 24 (L)
US$16		 END POINT EXPANDER & REVERSER.
Reverses servo & adjusts servo centre end points from 90o full throw to 180o full throw.
35 mm x 18 m x 7 mm
DUAL CONSTANT BRIGHTNESS R/C SWITCH FOR AUTOMATIC FORWARD & REVERSE LIGHTING.
Plugs In-Line and reads direction of Ch # 1 or Ch # 3 to change lighting direction.
Power by R/C BEC or Traction batteries. Provides 2 x Lighting controls.
For manual R/C control can be used with any spare centre idle channel.
MRW-SSLS
 A$29 (L)
US$20		 Solid State Lighting Switch.
Lights are ON before loco moves.
Also useable with battery R/C ESC's
PDF Instruction
 

CLICK HERE FOR INSTRUCTIONS ON HOW TO USE THE
DELTANG Rx102-1(AB) RX's

CLICK HERE FOR INFORMATION ON BASIC & ADVANCED LIVE STEAM R/C EQUIPMENT.
 
CLICK HERE FOR INFORMATION ON CENTRE OFF & LOW OFF HI POWERED BATTERY  R/C
ELECTRONIC SPEED CONTROLLERS.